← Back
Various coordination behavior of coumarin appended Schiff bases towards Ruthenium(II) ion: Synthesis, spectral characterization and biological evaluation
Journal of Geoscience and Environment Protection, 2024, 12, 57-74
https://www.scirp.org/journal/gep
ISSN Online: 2327-4344
ISSN Print: 2327-4336
Modeling Dispersion in the Event of a Leak
Ammonia Storage in a Hypothetical Uranium
Hexafluoride Production Plant
Camila Stramandinoli Deamatis, Nilce Ortiz
Institute for Nuclear and Energy Research, São Paulo, Brazil
How to cite this paper: Deamatis, C. S., &
Ortiz, N. (2024). Modeling Dispersion in the
Event of a Leak Ammonia Storage in a Hypothetical Uranium Hexafluoride Production Plant. Journal of Geoscience and Environment Protection, 12, 57-74.
https://doi.org/10.4236/gep.2024.1212004
Received: September 12, 2024
Accepted: December 14, 2024
Published: December 17, 2024
Copyright © 2024 by author(s) and
Scientific Research Publishing Inc.
This work is licensed under the Creative
Commons Attribution International
License (CC BY 4.0).
http://creativecommons.org/licenses/by/4.0/
Open Access
Abstract
The primary use of ammonia in nuclear plants is in producing uranium hexafluoride (UF6), a critical compound for uranium enrichment (U-235). Ammonia’s widespread use across multiple industries has led to a steady increase
in its production over the years. However, due to its toxic properties, conducting comprehensive studies on its dispersion is essential, as leaks can pose significant risks to human health and the environment. Tools like the Areal Locations of Hazardous Atmospheres (ALOHA) system are employed to model
the dispersion patterns of hazardous gases, enabling the prediction of toxic
substance releases and their spread. This study evaluates ammonia dispersion
in scenarios involving tank punctures or valve ruptures, which can lead to accidental leaks, particularly in uranium hexafluoride production facilities. The
meteorological factors considered in the dispersion modeling are wind speed,
temperature, humidity, and prevailing wind directions. The results demonstrate that low wind speeds and high temperatures significantly impact ammonia dispersion, while fluctuations in humidity have a minimal effect. Furthermore, the observed findings indicate that the prevailing wind direction in the
site tends to be most commonly from the East-Southeast (ESE). In this direction, dispersion extends towards vegetated areas and certain uranium hexafluoride production plant sections. However, the results highlight the wind direction variability over time, prompting further investigation into additional simulation scenarios.
Keywords
Ammonia, Uranium Hexafluoride, Nuclear Power Plant, ALOHA, Toxic Gas
Dispersion
1. Introduction
Ammonia has diverse applications across a range of chemical industries. It is
DOI: 10.4236/gep.2024.1212004
Dec. 17, 2024
57
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
widely used in fertilizer production to enhance the growth of crops, grasses, and
plants and in the pharmaceutical and textile sectors. Additionally, ammonia acts
as an intermediate product in manufacturing plastics and other chemical compounds (Environmental Company of the State of São Paulo, 2021; Rosa et al.,
2021). In the fertilizer industry, ammonia is crucial as a primary nitrogen source
and vital for plant cultivation (Afif et al., 2016). Its excellent heat transfer properties also make it a popular choice for refrigeration systems (Rosa et al., 2021).
In uranium hexafluoride (UF 6) plants, ammonia is primarily used in the
synthesis of ammonium diuranate (ADU-(NH4)2U2O7). This synthesis occurs
through the reaction of uranyl nitrate (UO2(NO3)2) with ammonia, either in its
gaseous or aqueous form, leading to the precipitation of ADU. The resulting compound is then calcined to produce UO3, the initial form of uranium oxide (Paik et
al., 2013). The process continues with reducing UO3 to UO2, followed by hydrofluorination to produce UF4. The final stage involves reacting UF4 with F2 to
produce uranium hexafluoride (UF6) (Manna et al., 2017; Morel & Duperret,
2009).
The toxicity of ammonia underscores the significant concern surrounding potential leaks. Any accidental release of ammonia into the environment poses a
rapid spread risk, potentially harming nearby individuals and ecosystems (Ng et
al., 2023). Accidents in industrial facilities can occur due to pipeline leaks, incidents during transportation, or storage of gases and liquid materials (Casal, 2018).
Due to the number of chemical industries and the handling of large quantities of
hazardous substances, the frequency of chemical accidents has risen. These accidents often result from human error, inadequate training, manufacturing defects,
and poor storage management (Anjana, Amarnath, & Nair, 2018). Hence, predicting the behavior of poisonous releases is paramount (Casal, 2018).
The Areal Location of Hazardous Atmosphere (ALOHA) system is a computational tool for assessing toxic gas dispersion. Its primary objective is to estimate
common hazards associated with accidental spills of volatile and flammable chemicals. It facilitates pre-planning and emergency response efforts by generating scenarios based on various factors such as location, chemical properties, atmospheric
conditions, and the type of chemical source. Additionally, it shows threat zones
and distances from the hazard source (National Oceanic and Atmospheric Administration, 2013; Hoscan & Cetinyokus, 2021).
ALOHA graphically represents a threat zone, where exposure to toxic vapors,
an explosive atmosphere, overpressure from a vapor cloud explosion, or thermal
radiation from the fire is possible. The represented threat zones are red, orange,
and yellow, where the red zone is the most significant threat zone (National Oceanic and Atmospheric Administration, 2013). The threat zones feature Levels of
Concern (LOCs), which are essential tools for assessing the impact of toxic air
emissions. LOCs represent specific concentrations of airborne chemicals associated with adverse health effects. ALOHA provides the following guidelines as
LOCs: Acute Exposure Guideline Levels (AEGLs), Emergency Response Planning
DOI: 10.4236/gep.2024.1212004
58
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Guidelines (ERPGs), Protective Action Criteria (PACs), and Immediate Danger
to Life and Health (IDLH) limits. In this study, the AEGL parameter was selected
(National Oceanic and Atmospheric Administration, 2013).
The Acute Exposure Guideline Levels established by a committee composed of
members from the United States Environmental Protection Agency (EPA) and
industry representatives. AEGL levels classification were according to the severity
of the toxic effects resulting from exposure, with level 1 being the least severe and
level 3 being the most severe (National Academy of Sciences USA, 2008). Follows
a brief from of these three levels:
AEGL-1: Represented by the color yellow. It may result in notable discomfort,
irritation, or non-sensible, asymptomatic effects. These effects are not disabling and are temporary, reversing after exposure stops.
AEGL-2: Represented by the color orange, it may result in adverse health effects with irreversible, serious, and long-lasting implications.
AEGL-3: The red indicates a concentration above which the general population, including susceptible individuals, is at risk of experiencing life-threatening or lethal effects.
Google Earth or Google Maps show the treat zones using ALOHA’s export feature Keyhole Markup Language (KML) file format (National Oceanic and Atmospheric Administration, 2020).
Meteorological factors, such as wind speed, temperature, and atmospheric pressure, among others, directly impact the dispersion of pollutants and the extent to
vulnerable areas (Sanchez et al., 2018; Chakrabarti & Parikh, 2011). Different meteorological variables influence the atmospheric dispersion of pollutants (National Institute of Meteorology, 2024). For example, wind speed considerably influences the dispersion of a chemical product and the extension of impact zones
(Sanchez et al., 2018; Inanloo & Tansel, 2015). Although wind speed is a significant factor, other variables, such as temperature and humidity, must also be considered (Sanchez et al., 2018).
The study of ammonia gas dispersion is important due accidents involving this
toxic substance can lead environmental and societal impacts (Tan et al., 2017).
This substance is corrosive and, when released, poses dangers to humans and
wildlife in the area (Ng et al., 2023). The ammonia forms ammonium hydroxide
and produces heat when it contacts moist surfaces, such as mucous membranes.
Due to its exothermic and corrosive properties, ammonia can cause severe irritation and burns to the eyes, skin, and mucous membranes of the oral cavity and
respiratory tract (National Academy of Sciences USA, 2008).
Given the unique characteristics of each industrial process, existing studies
typically provide insight only into the specific area where they were conducted
(Pouyakian et al., 2023). Therefore, while ammonia dispersion modeling has been
explored in various contexts, it is essential to analyze each process’s specific scenarios and conditions individually. This study evaluates data to assess the potential consequences of a hypothetical ammonia leak in a uranium hexafluoride
DOI: 10.4236/gep.2024.1212004
59
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
production facility. However, the ammonia dispersion values obtained in this
study can be applied to other industries that store ammonia, provided they have
similar tank characteristics and weather conditions to those in this research.
2. Materials and Methods
Figure 1 illustrates the methodology employed in this study. Initially, an investigation assessed the characteristics of the studied area, storage conditions, and local
meteorological conditions. Together with the initial conditions of ALOHA’s program, this information is essential to establish the threat zone.
Figure 1. Methodology summary used to stablish the threat zone.
2.1. Study Area
The hypothetical UF6 production unit used in this study has a 5000-liter ammonia
storage tank. The vertical tank is 2 meters long and 1.78 meters wide.
2.2. Meteorological Conditions
Different meteorological variables influence the atmospheric dispersion of pollutants (Casal, 2018). Information such as wind speed and direction, temperature,
and humidity is mandatory for simulations. This study used the meteorological
data obtained from the automatic station of the National Institute of Meteorology
(INMET). The INMET aims to generate meteorological information through
monitoring, analysis, weather, and climate forecasting (National Institute of Meteorology, 2024).
The wind rose graphically represents the frequency of winds according to their
direction and speed. So, obtaining information about wind behavior in a specific
geographical area is possible. The wind direction represents the wind blows. For
example, a north wind direction indicates that it blows from the north towards
the south (Casal, 2018).
Figure 2 represents the annual average for the year 2023. It illustrates that the
prevailing wind direction throughout that year was between east (E) and southeast
(SE).
DOI: 10.4236/gep.2024.1212004
60
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Figure 2. The wind rose chart for the site.
The meteorological data used in this study were obtained from the INMET automatic station, with records available from the start of its operations in August
2006 until December 2023. Variables such as wind speed, temperature, and relative humidity were analyzed specifically during nighttime periods, as the simulations were conducted during this time frame. Figures 3-5 show the distribution
of wind speed, temperature, and humidity, respectively, represented by histograms. This study considered that INMET performs regular calibrations on its
stations, ensuring data reliability. However, some values were not recorded in the
database. The table detailing the number of recorded and missing data is available
in Appendix A of this paper.
Figure 3 shows a histogram with the percentage of occurrences of different
wind speed ranges during nighttime from 2006 to 2023 and the number of times
each range occurs is represented above each bar in the histogram. Pearson’s skewness coefficient of 1.18 confirms the positive skewness, indicating that the data
have a longer tail to the right. In another words, the highest bars in the histogram
correspond to wind speeds between 0 and 5 meters per second, this indicates that
wind tends to be calmer during nighttime. Although most wind speed measurements are low, there are some extreme values above 10 meters per second, though
these occur at relatively small percentages.
Figure 4 presents the distribution of temperature during nighttime. The nighttime
temperature distribution was found to be nearly symmetrical, with a Pearson’s skewness coefficient of 0.20, indicating a predominance of slightly higher temperatures
during the nighttime, but the skewness is minimal, suggesting a relatively
DOI: 10.4236/gep.2024.1212004
61
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
balanced distribution between lower and higher temperatures. The most frequent
nighttime temperatures are concentrated around 20˚C, representing about 16% of
observations. Although there is this concentration of temperatures, the histogram
shows that extreme temperatures, such as those above 30˚C or below 10˚C, also
occur, albeit with a frequency less than 2%1.
Figure 3. Histogram of wind speeds during the nighttime period from 2006 to 2023.
Figure 4. Histogram of temperature during the nighttime period from 2006 to 2023.
Artificial intelligence technology by OpenAI, was used to assist in reviewing the text in this paragraph.
1
DOI: 10.4236/gep.2024.1212004
62
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
The histogram in Figure 5 shows the humidity distribution and a Pearson’s
skewness coefficient of −1.05, representing a left-skewed distribution. This means
that most humidity values are concentrated between 80% and 100% during the
nighttime.
Figure 5. Histogram of humidity during the nighttime period from 2006 to 2023.
The histograms illustrating the distributions of minimum and maximum wind
speeds, maximum and minimum temperatures, and maximum and minimum humidity in Figures 3-5 provide a comprehensive view of the climatic variations in
the dataset from 2006 to 2023. While there are fluctuations throughout the year,
a consistent trend can be identified over the different years analyzed.
2.3. Scenarios Studied
Table 1 describes the data used as initial conditions at ALOHA for all simulations,
including the chemical product, location, tank dimensions, hole diameter, and
wind directions. This information is essential for modeling the leak scenario and
analyzing the possible consequences.
Table 1. Data summary for ALOHA modeling.
Data summary
DOI: 10.4236/gep.2024.1212004
Chemical Name
Ammonia (NH3)
CAS Number
7664-41-7
Wind direction
ESE, NWN e SW
63
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Continued
Tank volume
5000 liters
Tank length
02 meters
Tank Diameter
1.78 meters
Time
Night
Opening diameter
0.5 centimeters
This research analyzes ammonia dispersion, varying the observation points and
variations in wind speed, temperature, and humidity. Five scenarios were conducted, each focusing on analyzing a different meteorological condition parameter. Within these parameters, several simulations were carried out. The scenarios
are described in Figure 6. The methodology employed in this study is similar to
that of Sanchez et al. (2018) and Anjana et al. (2018), utilizing diverse scenarios to
predict ammonia dispersion. This approach enables a more comprehensive analysis of meteorological conditions and their effects on dispersion.
Figure 6. Scenarios studied under different meteorological conditions.
3. Results and Discussions
The extreme values used in the simulations were determined by analyzing the data
provided by INMET from August 2006 to December 2023 (National Institute of
Meteorology, 2024).
3.1. Scenario 1: Wind Speed Variations
Maximum wind speed:
The highest wind speed recorded since August 2006 was November 03, 2023, at
25.4 meters per second. The temperature used in the simulation was 20.3˚C, the
average recorded on this date. In the conditions adopted for this simulation, the
reach of the toxic ammonia cloud for AEGL 3, AEGL 2, and AEGL 1 were 10, 18,
and 42 meters, respectively.
Minimum wind speed:
The lowest wind speed recorded since 2006 was zero meters per second. However, the minimum speed allowed by ALOHA is one meter per second. Therefore,
DOI: 10.4236/gep.2024.1212004
64
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
the adopted value was for the simulation. In this case, the temperature used in this
simulation was 20.3˚C and the humidity 50%, matching the previous simulation’s
conditions and allowing a comparison of the toxic gas dispersion, where the only
variable was the wind speed. In this simulation, with the minimum wind speed,
the reach of the harmful ammonia cloud for AEGL 3, AEGL 2, and AEGL 1 were
74, 204, and 511 meters, respectively.
Wind Speed Variations:
The study includes some additional scenarios to analyze the impact of wind
speed on ammonia dispersion. Table 2 summarizes the meteorological data used
in the ALOHA modeling for this scenario. These simulations of wind speed variations demonstrate that as wind speed decreases, the distance the gas reaches increases, as shown in the results in Figure 7.
Table 2. Meteorological conditions for ALOHA modeling—Wind speed variation.
Meteorological Conditions
Wind speed (m/s)
1
2
3
4
5
7
10
13
15
18
22
25.4
Temperature (˚C)
20.3
20.3
20.3
20.3
20.3
20.3
20.3
20.3
20.3
20.3
20.3
20.3
Humidity (%)
50
50
50
50
50
50
50
50
50
50
50
50
Figure 7. Threat zone behavior according to wind variation.
Among the simulations considering different wind speeds, the greatest ammonia dispersion occurred at a wind speed of 1 meter per second. The increase in
ammonia dispersion compared to the dispersion observed at a maximum speed
of 25.4 meters per second is 640% for AEGL-3, 1033.33% for AEGL-2, and
1116.67% for AEGL-1.
Wind is a relevant parameter for gas dispersion (Anjana, Amarnath, & Nair,
2018; Tan et al., 2017; Casal, 2018). The simulations indicate that a decrease in
wind speed increases ammonia dispersion, with larger areas affected by the gas
plume. According to Casal (2018), concentrations in a plume are inversely
DOI: 10.4236/gep.2024.1212004
65
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
proportional to wind speed, as wind exerts a dragging effect on the gas cloud.
Thus, the results of these simulations on wind speed variations align with Casal’s
(2018) assertion that wind speed directly affects the dispersion of gas clouds, with
stronger winds dispersing the gas more quickly and reducing the threat range.
Although wind speed is a significant factor, other meteorological variables must
also be considered (Sanchez et al., 2018). Accordingly, additional simulations were
conducted in this study and are presented below.
3.2. Scenario 2: Temperature Variations
Maximum temperature
The highest temperature recorded since 2006 was 38.8˚C on October 07, 2020.
The average wind speed recorded that day was 3.4 meters per second. In the conditions adopted for the simulation, the range of the toxic ammonia cloud, according to concentrations for AEGL 3, reaches 40 meters; for AEGL 2, it is 108 meters;
and for AEGL 1, it is 263 meters.
Minimum temperature
The lowest temperature recorded since 2006 in winter was 1.9˚C on October
05, 2021. The wind speed used was 3.4 meters per second, the same speed used in
the maximum temperature simulation, so it was possible to compare the distance
reached by the gas. The dispersion range of the toxic ammonia cloud for the conducted simulation was as follows: for AEGL 3, it extended to 21 meters; for AEGL
2, it reached 56 meters; and for AEGL 1, it extended to 134 meters.
Temperature Variations:
The study includes seven additional points to assess the effect of temperature
variations on ammonia dispersion. The summary of data on meteorological conditions used in ALOHA modeling for this scenario is presented in Table 3. The
results are in Figure 8. The results show that an increase in temperature favors
ammonia dispersion. The findings indicate that increasing temperature favors the
dispersion of ammonia. The increase in ammonia dispersion compared to the
minimum and maximum temperatures was 90.48% for AEGL-3, 92.86% for
AEGL-2, and 96.27% for AEGL-1.
Table 3. Meteorological conditions for ALOHA modeling—Temperature variation.
Meteorological Conditions
Temperature (˚C)
1
1.9
5
10
15
20
25
30
35
38.8
Wind speed (m/s)
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
Humidity (%)
50
50
50
50
50
50
50
50
50
50
The temperature variation simulations in this study and those by Bondžić et al.
(2021) suggest that higher temperatures increase the area at risk from ammonia
dispersion. Although the plume’s reach was less significant than wind speed variations, the results still show that temperature plays a role in gas dispersion. Casal
(2018) highlights that wind speed and direction are the dominant factors in gas
DOI: 10.4236/gep.2024.1212004
66
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
cloud dispersion, while temperature has a comparatively smaller effect.
Figure 8. Threat zone behavior considering to temperature variation.
3.3. Scenario 3: Humidity Variations
This research also considered the humidity variation, which ranged from a minimum value of 0% to a maximum of 100%. In this case, the scenario was a temperature of 20˚C and a wind speed of 3.4 meters per second. Table 4 summarizes
the data on meteorological conditions used in ALOHA modeling for this scenario.
The results presented in Figure 9 showed that altering humidity values does not
result in any variation in the distance reached by the gas, indicating that variations
in humidity do not affect ammonia dispersion.
Table 4. Meteorological conditions for ALOHA modeling—humidity variation.
Meteorological Conditions
Humidity (%)
0
10
20
30
40
50
60
70
80
90
100
Temperature (˚C)
20
20
20
20
20
20
20
20
20
20
20
Wind speed (m/s)
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
3.4
Figure 9. Threat zone behavior according to humidity variation.
DOI: 10.4236/gep.2024.1212004
67
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
In this study, humidity was considered, but it did not affect ammonia dispersion. Similarly, the research conducted by Silva Júnior, de Oliveira, and Fiates
(2022) indicates that humidity is an irrelevant factor in ammonia dispersion.
3.4. Scenario 4: Critical Variations
In the simulations with varying wind speeds, the speed increased when the toxic
cloud decreased. On the other hand, increasing temperature favors dispersion in
models when temperature changes. However, with humidity, no change in the
dispersion range was observed. This scenario involved studying the worst case observed for ammonia dispersion in Scenarios 1 and 2. Scenario 1, where the wind
variation on ammonia dispersion was studied and observed with a wind speed of
1 meter per second, resulted in the greatest dispersion. Scenario 2, which examined temperature variation, found that a temperature of 38.8˚C led to the greatest
ammonia dispersion. Therefore, the study used these values for the simulation in
this scenario. Since humidity proved irrelevant, the value of 50% remained constant. The simulation results consider the parameters presented in Figure 10.
Figure 10 shows the threat zone for this simulation. The dispersion range of
the toxic ammonia cloud for AEGL 3 extended to 101 meters; for AEGL 2, it
reached 280 meters; and for AEGL 1, it extended to 710 meters.
Figure 11 presents a Graphic representation of the threat zone. Considering the
most relevant wind direction, ESE, the average gas dispersion affects uninhabited
regions. However, the red danger zone affects part of the uranium hexafluoride
unit, becoming a concern for workers. Another area of concern susceptible to impact is the vegetation surrounding the installation, which may harbor wildlife at
risk of exposure. Safeguarding both the workers and the local environment is paramount.
Figure 10. Threat zone obtained using the ALOHA for Scenario 4.
Risk modeling based on realistic worst-case scenarios is necessary to minimize
potential risk and can provide a more accurate description of the consequences in
DOI: 10.4236/gep.2024.1212004
68
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
extreme situations (Juwari et al., 2024). Therefore, this scenario involved studying
previous scenarios’ worst-case observations for ammonia dispersion.
3.5. Scenario 5: Wind Direction Variations
As previously discussed, the wind exhibits different directions over time. Given
this variability, in addition to the simulation in the East-Southeast (ESE) direction,
simulations were also conducted in the West-Northwest (WNW) and Southwest
(SW) directions to investigate the areas affected by ammonia dispersion. Studying
these scenarios aims to assess the impacts under different wind conditions. The
WNW and SW directions were selected for these simulations because, according
to the wind rose shown in Figure 2, they were the other predominant directions.
The dispersion range of the toxic ammonia cloud in this simulation was: for
AEGL 3, it extended to 101 meters; for AEGL 2, it reached 280 meters; and for
AEGL 1, it extended to 710 meters. Figure 11 shows the graphical representation
for the East-Southeast, West-Northwest, and Southwest directions.
As wind direction changes over time, estimating the vulnerable population in
different directions around the hazardous materials storage facility is essential for
effective preparedness and timely evacuation in the event of an accident (Anjana,
Amarnath, & Nair, 2018). Therefore, other directions were simulated. Based on
the simulations conducted for this scenario, it is observed that in the event of an
accident with wind blowing in the West-Northwest (WNW) and Southwest (SW)
directions, ammonia dispersion does not extend beyond the nuclear plant’s premises. The affected area remains confined to the nuclear plant, without impacting
inhabited regions. This means that under these specific wind conditions, there is
no risk of ammonia contamination for nearby communities. However, considering the most relevant wind direction, ESE, the gas dispersion also affects uninhabited regions. Another area susceptible to impact is the vegetation zone. Additionally, in all directions, the AEGL-3 zone affects part of the uranium hexafluoride
unit, making it a concerning area for the facility’s workers.
Given its toxicity, ammonia leakage poses a significant concern, as any accidental release of ammonia into the environment risks spreading quickly and causing harm to nearby individuals and damage to the ecosystem (Ng et al., 2023). The
harm caused by NH3 to humans, animals, and the environment should not be underestimated (Wang et al., 2022). Because exposure to ammonia can lead to various pulmonary symptoms in workers’ respiratory systems (Soltanzadeh et al.,
2024). According to Casal (2018), predicting the behavior of a toxic release enables
an assessment of the accident’s effects. This provides essential information for developing safety measures and emergency response plans. Implementing practical
strategies and technical solutions can effectively decrease vulnerability to such incidents (Soltanzadeh et al., 2024).
In the study, the affected area does not impact inhabited regions; however, it
does affect the plant area, which can pose risks to workers in that area. To minimize the risk in the event of an accidental leak, the study by Anjana et al. (2018)
DOI: 10.4236/gep.2024.1212004
69
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Figure 11. Graphical representation of the threat zone – Directions ESE, WNW and SW.
proposes measures for ammonia storage facilities to mitigate potential risks, such
as: the construction of high walls around the ammonia storage facility can prevent
ammonia dispersion by inhibiting the wind effect, and water spray nozzles controlled by ammonia detectors can be installed since ammonia is soluble in water,
thereby reducing risks and preventing air pollution. With the installation of water
spray nozzles suggested by Anjana et al. (2018), a warning system could be integrated to alert workers and emergency response teams. Alongside this, the development of an Emergency Action Plan (EAP) becomes necessary, as simulation
training for evacuating the affected area can ensure that everyone knows how to
respond adequately to emergencies2.
4. Conclusion
This study demonstrates that the meteorological conditions with the greatest impact on ammonia dispersion are low wind speeds and high temperatures, while
variations in humidity showed minimal influence on gas dispersion. Additionally,
it was found that the prevailing wind direction in the analyzed region is EastSoutheast (ESE). However, since wind direction varies over time, other predominant directions were also considered. The simulations revealed that, regardless of
wind direction, ammonia dispersion affects the facility, and the ESE direction impacts surrounding vegetation. This raises concerns for the safety of workers, and
local wildlife.
As a result, implementing preventive measures is essential. Regular inspections
of tanks, valves, and pipelines should be conducted to ensure the integrity of ammonia storage infrastructure. Although the likelihood of an accident is low, this
Artificial intelligence technology by OpenAI, was used to assist in reviewing the text in this paragraph.
2
DOI: 10.4236/gep.2024.1212004
70
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
study underscores the importance of having a comprehensive Emergency Action
Plan in place. This plan should include personnel training for proper evacuation
procedures in the event of a leak. By increasing awareness and preparedness among
facility workers, potential damage can be minimized, and an effective emergency
response can be ensured.
Since factors such as weather conditions and storage variables—like tank size,
stored volume, and location directly influence the dispersion of toxic gases such
as ammonia, each industry must conduct studies tailored to its specific context.
Therefore, future research can focus on assessing operational risks involving conditions that were not addressed in this study.
Acknowledgements
National Institute of Meteorology (INMET) for providing essential meteorological data, which was crucial for the analyses conducted in this study.
Conflicts of Interest
The authors declare no conflicts of interest regarding the publication of this paper.
References
Afif, A., Radenahmad, N., Cheok, Q., Shams, S., Kim, J. H., & Azad, A. K. (2016). Ammonia-Fed Fuel Cells: A Comprehensive Review. Renewable and Sustainable Energy Reviews, 60, 822-835. https://doi.org/10.1016/j.rser.2016.01.120
Anjana, N. S., Amarnath, A., & Nair, M. V. H. (2018). Toxic Hazards of Ammonia Release
and Population Vulnerability Assessment Using Geographical Information System.
Journal of Environmental Management, 210, 201-209.
https://doi.org/10.1016/j.jenvman.2018.01.021
Bondžić, J., Sremački, M., Popov, S., Mihajlović, I., Vujić, B., & Petrović, M. (2021). Exposure to Hazmat Road Accidents—Toxic Release Simulation and GIS-Based Assessment
Method. Journal of Environmental Management, 293, Article 112941.
https://doi.org/10.1016/j.jenvman.2021.112941
Casal, J. (2018). Introduction. In J. Casal (Ed.), Evaluation of the Effects and Consequences
of Major Accidents in Industrial Plants (pp. 1-24). Elsevier.
https://doi.org/10.1016/b978-0-444-63883-0.00001-0
Chakrabarti, U. K., & Parikh, J. K. (2011). Class-2 Hazmat Transportation Consequence
Assessment on Surrounding Population. Journal of Loss Prevention in the Process Industries, 24, 758-766. https://doi.org/10.1016/j.jlp.2011.04.011
Environmental Company of the State of São Paulo (2021). Ammonia.
https://cetesb.sp.gov.br/laboratorios/wp-content/uploads/sites/24/2021/05/Amônia.pdf
Hoscan, O., & Cetinyokus, S. (2021). Determination of Emergency Assembly Point for Industrial Accidents with AHP Analysis. Journal of Loss Prevention in the Process Industries, 69, Article 104386. https://doi.org/10.1016/j.jlp.2020.104386
Inanloo, B., & Tansel, B. (2015). Explosion Impacts during Transport of Hazardous Cargo:
GIS-Based Characterization of Overpressure Impacts and Delineation of Flammable
Zones for Ammonia. Journal of Environmental Management, 156, 1-9.
https://doi.org/10.1016/j.jenvman.2015.02.044
Juwari, J., Anugraha, R. P., Zanata, M., Leksono, N. A., Hamid, M. D., & Cahyono, T.
DOI: 10.4236/gep.2024.1212004
71
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
(2024). Quantitative Risk Assessment and Risk Reduction of Worst-Case Accident Scenario at Fuel Storage Terminal. Journal of Loss Prevention in the Process Industries, 88,
Article 105272. https://doi.org/10.1016/j.jlp.2024.105272
Manna, S., Kumar, R., Satpati, S. K., Roy, S. B., & Joshi, J. B. (2017). Study of the Changes
in Composition of Ammonium Diuranate with Progress of Precipitation, and Study of
the Properties of Ammonium Diuranate and Its Subsequent Products Produced from
Both Uranyl Nitrate and Uranyl Fluoride Solutions. Nuclear Engineering and Technology, 49, 541-548. https://doi.org/10.1016/j.net.2016.09.005
Morel, B., & Duperret, B. (2009). Uranium and Fluorine Cycles in the Nuclear Industry.
Journal of Fluorine Chemistry, 130, 7-10. https://doi.org/10.1016/j.jfluchem.2008.05.022
National Academy of Sciences USA (2008). Acute Exposure Guideline Levels for Selected
Airborne Chemicals.
https://www.epa.gov/sites/default/files/2014-11/documents/ammonia_final_volume6_2007.pdf
National Institute of Meteorology (2024). Instituto Nacional de Meteorologia.
https://tempo.inmet.gov.br/Graficos/A001
National Oceanic and Atmospheric Administration (2013). ALOHA® (Areal Locations of
Hazardous Atmospheres) 5.4.4: Technical Documentation.
https://nepis.epa.gov/Exe/ZyPDF.cgi/P1003UZB.PDF?Dockey=P1003UZB.PDF
National Oceanic and Atmospheric Administration (2020). ALOHA—Areal Locations of
Hazardous Atmospheres Fact Sheet. https://response.restoration.noaa.gov
Ng, C. K. L., Liu, M., Lam, J. S. L., & Yang, M. (2023). Accidental Release of Ammonia
during Ammonia Bunkering: Dispersion Behaviour under the Influence of Operational
and Weather Conditions in Singapore. Journal of Hazardous Materials, 452, Article
131281. https://doi.org/10.1016/j.jhazmat.2023.131281
Paik, S., Biswas, S., Bhattacharya, S., & Roy, S. B. (2013). Effect of Ammonium Nitrate on
Precipitation of Ammonium Di-Uranate (ADU) and Its Characteristics. Journal of Nuclear Materials, 440, 34-38. https://doi.org/10.1016/j.jnucmat.2013.04.011
Pouyakian, M., Ashouri, M., Eidani, S., Madvari, R. F., & Laal, F. (2023). A Systematic Review of Consequence Modeling Studies of the Process Accidents in Iran from 2006 to
2022. Heliyon, 9, e13550. https://doi.org/10.1016/j.heliyon.2023.e13550
Rosa, A. C., de Souza, I. T., Terra, A., Hammad, A. W., Di Gregório, L. T., Vazquez, E. et
al. (2021). Quantitative Risk Analysis Applied to Refrigeration’s Industry Using Computational Modeling. Results in Engineering, 9, Article 100202.
https://doi.org/10.1016/j.rineng.2021.100202
Sanchez, E. Y., Represa, S., Mellado, D., Balbi, K. B., Acquesta, A. D., Colman Lerner, J. E.
et al. (2018). Risk Analysis of Technological Hazards: Simulation of Scenarios and Application of a Local Vulnerability Index. Journal of Hazardous Materials, 352, 101-110.
https://doi.org/10.1016/j.jhazmat.2018.03.034
Silva Júnior, A. H., de Oliveira, C. R. S., & Fiates, J. (2022). Numerical Experimental Design
Application in Consequence Analysis of Ammonia Leakage. Chemical Engineering Journal Advances, 11, Article 100327. https://doi.org/10.1016/j.ceja.2022.100327
Soltanzadeh, A., Mahdinia, M., Nikbakht, N., Hosseinzadeh, K., & Sadeghi-Yarandi, M.
(2024). Evaluation of Human Vulnerability and Toxic Effects of Chronic and Acute Occupational Exposure to Ammonia: A Case Study in an Ice Factory. Work, 78, 1021-1033.
https://doi.org/10.3233/wor-230106
Tan, W., Du, H., Liu, L., Su, T., & Liu, X. (2017). Experimental and Numerical Study of
Ammonia Leakage and Dispersion in a Food Factory. Journal of Loss Prevention in the
DOI: 10.4236/gep.2024.1212004
72
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Process Industries, 47, 129-139. https://doi.org/10.1016/j.jlp.2017.03.005
Wang, A., Zhang, X., Wang, H., & Xing, H. (2022). Recent Evidence for Toxic Effects of
NH3 Exposure on Lung Injury: Protective Effects of L-Selenomethionine. Ecotoxicology
and Environmental Safety, 242, Article 113937.
https://doi.org/10.1016/j.ecoenv.2022.113937
DOI: 10.4236/gep.2024.1212004
73
Journal of Geoscience and Environment Protection
C. S. Deamatis, N. Ortiz
Appendix
Table A1 presents the valid and unrecorded records by year (2006-2023) during
the night for the meteorological data used in this study. For unknown reasons,
some data were not recorded.
Table A1. Number of valid and invalid records by year from 2006 to 2023.
DOI: 10.4236/gep.2024.1212004
Year
Valid Records
Invalid Records
2006
1725
270
2007
4137
207
2008
4482
104
2009
4331
0
2010
4314
30
2011
4226
116
2012
4258
97
2013
4261
83
2014
4278
65
2015
4259
85
2016
4323
32
2017
4344
0
2018
4271
72
2019
3480
863
2020
4030
324
2021
1434
2910
2022
3185
1158
2023
4344
0
74
Journal of Geoscience and Environment Protection